Power-Flushing

What's a power flush?

A power flush is a process carried out by central heating engineers designed to remove sludgy build-up in the boiler, pipes and radiators that make up your central heating system. A power flushing unit sends water through your central heating system at high velocity to dislodge any build-up of sludge, rust and other debris.

This helps to improve the efficiency and lifespan of the boiler and central heating system and prevent breakdowns. As with so many plumbing issues, regular maintenance (including power flushing) is the best way to keep your system in shape. 

What happens during a power flush and how long does it take?

A powerful machine called a 'pumping station' is used to remove dirty water and sludgy build-up while introducing clean water. The engineer may add a chemical to the system to break down sludge before the equipment is connected and the flushing process begins.

The power flushing process has several stages and our engineer will probably take between several hours to the whole day to complete the power flush.

 Step one – following the equipment set-up, the engineer should spend around 90 minutes flushing the whole system (in both directions) and then they will tackle troublesome sections until they run clean. Your engineer will work on heavily contaminated radiators separately. They may use an ‘agitator’ (a tough pad attached to a hammer action drill) to help release internal build-ups of sludge.

Step two - after clearing out the system, the engineer will add a chemical neutraliser and wash it through the system. Then your engineer should check the PH balance to ensure the system is not too acidic, as excess acid can lead to internal corrosion.

 Step three – your engineer will add a dose of ‘inhibitor’ fluid to the system. This prevents corrosion and goes some way in preventing sludge building up again in the central heating system. Depending on the size and initial condition of the system, the complete process may well take all day.

When does my central heating system need a powerflush?

One or more of these symptoms could indicate that your central heating system would benefit from a powerflush:

• cold radiators with only a hot strip at the top
• black sludgy water in the heating system (shown by radiator removal or a failed heating pump or valve replacement)
• poor circulation to a system that used to work better
• a magnet attaching to copper pipe-work (signs of iron sludge within)
•  an overflowing attic header tank (although this could also be caused by a pump being set at the wrong speed). 

A powerflush can be a good idea, if you're having a new boiler installed but have an old central heating system with old-style radiators. Your boiler engineer can carry out visual and chemical checks which indicate the PH balance and levels of corrosive elements in the system. These will determine whether a full powerflush is needed. Sometimes a ‘dynamic flush’, using clean mains pressure water, is all that's needed. It is a requirement with every new boiler installation that the system is thoroughly flushed, although not necessarily ‘power flushed’

Remember that central-heating engineers are often less busy during the summer months when people do not think about their central-heating system. Of course they’re still available in colder months, but you may need to wait longer for an appointment.

Who should perform a powerflush?

A suitably qualified central heating engineer should carry out power flushing. This is not something to attempt yourself, particularly if your engineer also needs to open up your boiler or examine other faults in your central heating system.

Is powerflushing always the solution to central heating problems?

No. If there is a broken part in your boiler, or elsewhere in your central heating system, power flushing will not fix it. Power flushing can improve the efficiency of your system and keep it running effectively but it cannot mend valves that have broken as a result of sludge in the system, for example.

Equally, power flushing is not the solution to pressure loss. That usually indicates a leak in the system – again this may have occurred due to inefficient running, but the power flushing will not solve the problem by itself.

Power flushing works best if it is carried out regularly from when a system is new. If you have an older boiler and system (if it’s 15 years old or more) then power flushing might not work for you. In this case, it’d be more cost-effective to look at replacing the boiler, radiators and maybe some of the pipework, rather than trying to improve a failing system.

Because power flushing pushes water around your central heating system at high speed, it can increase pressure on any areas of weakness, such as rusting radiators. If there are any underlying weaknesses, it can lead to leaks.

Your central heating engineer should be able to evaluate whether power flushing is the best option for your system. If there is an underlying fault, our engineer will need to check the system thoroughly to find and remedy it. 

Will power flushing remove all the sludge in my central heating system?

No. It will remove a good proportion of it, but it cannot remove all the sludge in the system. If your system is very old or very heavily silted up, then power flushing may not be sufficient to remedy the problem.

Get in touch

To arrange your free quote, give us a call on 07758668234 or 07423397737 or email us at info@21degreeheating.com. You can also get in touch using our contact form and we will get back to you as soon as we can.